BSP452 E6327

Smart High-Side Power Switch BSP452 • High-side switch • Short-circuit protection • Input protection • Overtemperature protection with hysteresis • Overload protection • Overvoltage protection • Switching inductive load • Clamp of negative output voltage with inductive loads • Undervoltage shutdown • Maximum current internally limited • Electrostatic discharge (ESD) protection 1 • Reverse battery protection ) • AEC qualified SOT 223 •Package: Green product (RoHS compliant) Type Ordering code BSP 452 Q67000-S271 SOT-223 1 SOT-223 PG-SOT-223 Application • µC compatible power switch for 12 V DC grounded loads • All types of resistive, inductive and capacitive loads • Replaces electromechanical relays and discrete circuits General Description N channel vertical power FET with charge pump, ground referenced CMOS compatible input,monolithically integrated in Smart SIPMOS technology. Fully protected by embedded protection functions. Blockdiagramm: + Vbb Voltage Overvoltage Current Gate source protection limit protection V Logic ESDDiode Voltage Charge pump sensor Level shifter Rectifier 3 R IN 4 Limit for unclamped ind. loads OUT Temperature sensor 1 in Load ESD Logic miniPROFET GND 2 Signal GND 1) Load GND With resistor RGND=150 Ω in GND connection, resistor in series with IN connections reverse load current limited by connected load. Data Sheet 1 V1.0, 2007-05-25 Smart High-Side Power Switch BSP452 Pin Symbol Function 1 OUT O Output to the load 2 GND - Logic ground 3 IN I Input, activates the power switch in case of logical high signal 4 Vbb + Positive power supply voltage Maximum Ratings at Tj = 25 °C unless otherwise specified Parameter Supply voltage Load current self-limited 2) Maximum input voltage Maximum input current Inductive load switch-off energy dissipation, IL = 0.5A , TA = 150°C single pulse (not tested, specified by design) Load dump protection3) VLoadDump=UA+Vs RL= 24Ω RI=2Ω , td=400ms, IN= low or high, UA=13,5V RL= 80Ω (not tested, specified by design) Electrostatic discharge capability (ESD)5) PIN 3 PIN 1,2,4 Symbol Vbb IL VIN IIN EAS Operating temperature range Storage temperature range 6 Max. power dissipation (DC) ) TA = 25 °C Tj Tstg Ptot chip - soldering point: chip - ambient:6) RthJS RthJA Thermal resistance VLoad dump4) VESD Values 40 IL(SC) -5.0...Vbb ±5 0.5 Unit V A V mA J 60 80 V ±1 ±2 -40 ...+150 -55 ...+150 1.8 kV 7 70 K/W °C W 2) At VIN > Vbb, the input current is not allowed to exceed ±5 mA. Supply voltages higher than Vbb(AZ) require an external current limit for the GND pin, e.g. with a 150 Ω resistor in the GND connection A resistor for the protection of the input is integrated. 4) VLoad dump is setup without the DUT connected to the generator per ISO 7637-1 and DIN 40839 5) HBM according to MIL-STD 883D, Methode 3015.7 6) BSP 452 on epoxy pcb 40 mm x 40 mm x 1.5 mm with 6 cm2 copper area for Vbb connection 3) Data Sheet 2 V1.0, 2007-05-25 Smart High-Side Power Switch BSP452 Electrical Characteristics Parameter and Conditions Symbol Values typ max --- 0.16 -- 0.2 0.4 Ω 0.7 -- -- A ton toff --- 60 60 100 150 µs dV /dton -- 2 4 V/µs -dV/dtoff -- 2 4 V/µs VIN VIN(T+) -3.0 -- --- Vbb 3.5 V V VIN(T-) 1.5 -- -- V ∆VIN(T) IIN(off) -10 0.5 -- -60 V µA IIN(on) 10 -- 100 µA RIN 1.5 2.8 3.5 kΩ at Tj = 25 °C, Vbb = 13.5V unless otherwise specified min Load Switching Capabilities and Characteristics On-state resistance (pin 4 to 1) IL = 0.5 A, Vin = high Tj = 25°C Tj = 150°C 7) Nominal load current (pin 4 to 1) ISO Standard: VON = Vbb - VOUT = 0.5 V TS = 85 °C Turn-on time to 90% VOUT Turn-off time to 10% VOUT RL = 24 Ω Slew rate on 10 to 30% VOUT, RL = 24 Ω Slew rate off 70 to 40% VOUT, RL = 24 Ω Input Allowable input voltage range, (pin 3 to 2) Input turn-on threshold voltage Tj = -40...+150°C Input turn-off threshold voltage Tj = -40...+150°C Input threshold hysteresis Off state input current (pin 3) VIN(off) = 1.2 V Tj = -40...+150°C On state input current (pin 3) VIN(on) = 3.0 V to Vbb Tj = -40...+150°C Input resistance 7) RON IL(ISO) Unit IL(ISO) is limited by current limitation, see IL(SC), next page Data Sheet 3 V1.0, 2007-05-25 Smart High-Side Power Switch BSP452 Parameter and Conditions Symbol at Tj = 25 °C, Vbb = 13.5V unless otherwise specified min Operating Parameters Operating voltage8) Undervoltage shutdown Undervoltage restart Tj =-40...+150°C Tj =-40...+150°C Tj =-40...+25°C Tj =+150°C Undervoltage restart of charge pumpe see diagram page 77 Undervoltage hysteresis ∆Vbb(under) = Vbb(u rst) - Vbb(under) Overvoltage shutdown Tj =-40...+150°C Overvoltage restart Tj =-40...+150°C Overvoltage hysteresis Tj =-40...+150°C Standby current (pin 4), Vin = low Tj =-40...+150°C Operating current (pin 2), Vin = 5 V leakage current (pin 1) Vin = low Tj =-40...+25°C Tj =150°C Protection Functions Current limit (pin 4 to 1) Tj = 25°C Vbb = 20V Tj = -40...+150°C Overvoltage protection Ibb=4mA Tj =-40...+150°C Output clamp (ind. load switch off) at VOUT=Vbb-VON(CL), Ibb = 4mA Thermal overload trip temperature Thermal hysteresis 9 Inductive load switch-off energy dissipation ) Tj Start = 150 °C, single pulse, IL = 0.5 A, Vbb = 12 V (not tested, specified by design) 10 Reverse battery (pin 4 to 2) ) Vbb(on) Vbb(under) Vbb(u rst) Values typ 5.0 3.5 -- ---- Vbb(ucp) -- ∆Vbb(under) Unit max V V V 5.6 34 5 6.5 7.0 7 -- 0.3 -- V Vbb(over) Vbb(o rst) ∆Vbb(over) Ibb(off) IGND IL(off) 34 33 ----- --0.7 10 1 2 42 --25 1.6 5 7 V V V µA mA µA IL(SC) 1.5 --47 2 2.4 --- A Vbb(AZ) VON(CL) 0.7 0.7 41 41 V V Tjt ∆Tjt EAS 150 --- -10 -- --0.5 °C K J -Vbb -- -- 30 V V (not tested, specified by design) 8) At supply voltage increase up to Vbb= 5.6 V typ without charge pump, VOUT ≈Vbb - 2 V While demagnetizing load inductance, dissipated energy in PROFET is EAS= ∫ VON(CL) * iL(t) dt, approx. 2 V EAS= 1/2 * L * IL * (V ON(CL) ) ON(CL) - Vbb 10) Requires 150 Ω resistor in GND connection. Reverse load current (through intrinsic drain-source diode) is normally limited by the connected load. 9) Data Sheet 4 V1.0, 2007-05-25 Smart High-Side Power Switch BSP452 Max. allowable power dissipation Ptot = f (TA,TSP) Current limit characteristic IL(SC) = f (Von); (Von see testcircuit) Ptot [W] IL(SC) [A] 18 2 16 1.8 1.6 14 1.4 12 TSP 150°C 1.2 25°C 1 -40°C 10 8 0.8 6 0.6 4 0.4 TA 2 0.2 0 0 0 25 50 75 100 125 150 0 2 4 6 8 10 12 TA, TSP[°C] 14 Von [V] On state resistance (Vbb-pin to OUT-pin) RON = f (Tj); Vbb = 13.5 V; IL = 0.5 A Typ. input current IIN = f (VIN); Vbb = 13,5 V RON [Ω] IIN [µA] 0.4 50 -40°C 45 0.35 40 + 25°C 0.3 35 98% 0.25 +150°C 30 0.2 25 20 0.15 15 0.1 10 0.05 5 0 0 -50 -25 0 25 50 75 0 100 125 150 Tj [°C] Data Book Data Sheet 5 5 2 4 6 8 10 12 14 VIN [V] 20 08 96 V1.0, 2007-05-25 Smart High-Side Power Switch BSP452 Typ. operating current IGND = f (Tj); Vbb = 13,5 V; VIN = high Typ. overload current IL(lim) = f (t); Vbb = 13,5 V, no heatsink, Param.: Tjstart IGND [mA] IL(lim) [A] 0.8 1.4 0.7 1.2 0.6 1 0.5 0.8 +150°C 0.4 +25°C -40°C 0.6 0.3 0.4 0.2 0.2 0.1 0 0 -50 -25 0 25 50 75 100 125 150 -50 0 50 100 150 200 250 300 350 400 Tj [°C] t [ms] Typ. standby current Ibb(off) = f (Tj); Vbb = 13,5 V; VIN = low Short circuit current IL(SC) = f (Tj); Vbb = 13,5 V Ibb(off) [µA] IL(SC) [A] 8 1.4 7 1.2 6 1 5 0.8 4 0.6 3 0.4 2 0.2 1 0 -50 0 -50 -25 Data Sheet 0 25 50 75 100 125 150 -25 0 25 50 75 100 125 150 Tj [°C] Tj [°C] 6 V1.0, 2007-05-25 Smart High-Side Power Switch BSP452 Typ. input turn on voltage threshold VIN(T+) = f (Tj); Figure 6: Undervoltage restart of charge pumpe VIN(T+) [V] VON [V] 3 13V 2.5 2 V bb(over) 1.5 V 1 V bb(o rs t) bb(u rs t) V 0.5 bb(u c p) V bb(under) 0 -50 -25 0 25 50 75 100 125 150 Tj [°C] Vbb [V] charge pump starts at Vbb(ucp) about 7 V typ. Test circuit Typ. on-state resistance (Vbb-Pin to Out-Pin) RON = f (Vbb,IL); IL=0.5A, Tj = 25°C RON [mΩ] 300 250 200 150 100 50 0 0 5 10 15 20 25 Vbb [V] Data Sheet 7 V1.0, 2007-05-25 Smart High-Side Power Switch BSP452 Package Outlines 1.6 ±0.1 6.5 ±0.2 0.1 max +0.2 acc. to DIN 6784 1 2 3.5 ±0.2 4 0.5 min B 7 ±0.3 3 ±0.1 15˚max A 3 0.28 ±0.04 2.3 0.7 ±0.1 4.6 0.25 Figure 1 M 0.25 A M B PG-SOT-223 (Plastic Dual Small Outline Package) (RoHS-compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pbfree finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). Please specify the package needed (e.g. green package) when placing an order You can find all of our packages, sorts of packing and others in our Infineon Internet Page “Products”: http://www.infineon.com/products. Data Sheet 8 Dimensions in mm V1.0, 2007-05-25 Smart High-Side Power Switch BSP452 Revision History Version 1.0 Data Sheet Date Changes 2007-05-25 Creation of the green datasheet. First page : Adding the green logo and the AEC qualified Adding the bullet AEC qualified and the RoHS compliant features Package page Modification of the package to be green. 9 V1.0, 2007-05-25 Edition 2007-05-25 Published by Infineon Technologies AG 81726 Munich, Germany © Infineon Technologies AG 5/29/07. All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics (“Beschaffenheitsgarantie”). With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.